Page 13 Attach elevator adjustment 12 to pole bracket. Then, hinge board to match up with holes in First attach board 41 to upper yoke 17 , lower yoke 18 , FIG. Remove rim cover 16 , attach rim assembly 3 to backboard 41 and reattach rim cover Carefully cut and peel protective film away from Apply name plate sticker 27 to lower yoke as shown.
Page 17 Upright pole 1 by tightening nut Page 18 After pole has been secured to anchor plate 2 loosen nut 26 , remove cotter pin 37 , and pull out pin This will allow the removal of the threaded assembly rod 14 which is no longer necessary for the remainder of the assembly and installation of system.
Page 19 Check system leveling. Pole 1 should be level in all directions. After system is leveled, completely tighten all nuts NOTE: If adjustment is necessary, adjust system by rotating the nuts 25 between anchor plate 2 and pole flange. Apply height adjust ment label Adjust system by turning crank until desired height is reached per height indicator This manual is also suitable for: High end residential in-ground basketball system.
Print page 1 Print document 21 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Page 12 Install rod 12 through holes in bottom pole section 3 and eyebolt Insert pole assembly into tank 8 and through center hole on wheel assembly as shown.
Secure pole assembly with anchor strap 53 , washer 11 , and lock nut Page 13 Secure tank struts 14 to pole as shown. Place cap 15 over exposed end of bolt as shown. Page 14 Secure ends of tank struts 14 to tank as shown. Repeat for opposite side. Install upper pivot bracket 16 to front of base using bolt 19 , washer 20 and nut 47 as shown. Page 15 Insert bolt 21 through lower pivot bracket 17 as shown; bolt 21 will be secured during Step Carefully place base assembly on its side. Install lower pivot bracket 17 with bolt 23 , washers 20 , and lock nut 47 as shown.
Page 16 Insert axle 5 through wheel bracket 4. Secure wheels 6 to axle using pushnuts 7. Position base as shown. Secure wheel bracket assembly with disc 61 , washer 20 and nut 47 as shown. Page 18 Securely rest the assembly on sawhorse. Install pole bracket 36 to top pole as shown FIG. A using bolts 38 , metal spacers 60 and nuts Reference finished assembly FIG. Page 19 Identify elevator tubes. Install triangle plates 33 and elevator tubes 35 to top pole section 1 as shown.
Install pole cap Page 20 Attach label 57 to window Remove packaging materials and zip ties from handle assembly Snap window into handle assembly Page 21 Insert strut assembly 29 over inner channel 30A and between outer channel B. Rest at angle shown in FIG. Page 22 Attach hook 58 to strip 56 and secure with bolt 59 and nut Bring strip 56 through top of height indicator Install hook and strip 56 assembly window 27 underneath tabs and insert through into handle assembly.
Page 23 Attach strut 29 to pole bracket 36 with bolt 31 , washers 11 , and nut 55 as shown. Slip plastic spacers 25 onto metal spacer 44 that is already inserted into handle assembly. Then, secure handle assembly to elevator tubes 35 using bolts 40 , plastic spacers 24 and nuts Page 24 Secure strap and hook assembly to upper elevator arms 35 using bolt 40 , plastic spacers 32 and nut 37 as shown.
Page 25 Install spacers 28 onto backboard brackets 48 with bolts 64, 46 , washers 20 and lock nuts 55, 47 as shown. Assemble lower elevator tubes 35 as shown. NOTE: Tighten bolt 40 in locknut 37 until flush even with the outer edge of the locknut.
0コメント